The improved F_Series 200F3[X] ESCs. Building upon our trusted ARM 32-bit architecture, the V2 release features introduce a number of highly requested features into the product range, including configuration options and additional drive modes. The 200F3[X]v2 ESCs are drop-in replaceable to 200F3[X] units. As before, existing features include PWM-frequency dithering and Active Phase-Current Demagnetisation, allowing for smooth control with virtually all powertrain combinations with peak power outputs of up to 18 kW.

NDAA/DFARS-compliant options available upon request.

New Feature Set (V2):

• Configuration of drive parameters, signal types and fault handling

• On board bootloader

• Additional Telemetry types: PWM Telemetry and RPM Output

• High-speed telemetry rates when operating DShot

• Reversible operation support (full forwards to full reverse)

• Dynamic signal quality checks across supported input protocols

Feature Set:

• Designed and manufactured in Australia using only the highest quality components, ensuring no sacrifice in reliability

• Proprietary firmware designed in Australia

• Plug and play firmware

• Up to 14S (60 V) capable

• Up to 200 A continuous* output current

• 300 A Burst current

• True 10-bit resolution

• Virtually no setup time, with simple motor reverse solder tab

• Auto-detect PWM or DShot

• DShot150 to DShot600 capable (0.15-0.6Mbs/s)

• Up to 750,000 eRPM (protocol dependant)

• Motor agnostic

• Auto PWM output frequency

• Auto timing advance

• Telemetry output

• Automatic current limiting and over-temperature protection

• LED indication

• Digital commands over ProShot (including anti-turtle mode)

• Digital commands over DShot

• Bare-PCB design to allow maximum integration within the end setup

• 8-Layer PCB to ensure minimal track resistance

* Continuous current ratings are at a 100% throttle duty cycle.

Continuous rating is defined as max sustained current at 100% throttle for 60 seconds with 33 m/s of airflow.

Documentation and Datasheets can be found at: docs.powerdrives.net

Additional Information

Weight: 0.036kg

Dimensions: 73x34x20mm

Documentation: docs.powerdrives.net

CAD Model: 200F3 CAD Model

The improved F_Series 120F3[X] ESCs. Building upon our trusted ARM 32-bit architecture, the V2 release features introduce a number of highly requested features into the product range, including configuration options, Bi-Directional DShot, and UART overvoltage protection. The 120F3[X]v2 ESCs are drop-in replaceable to 120F3[X] units. As before, existing features include PWM-frequency dithering and Active Phase-Current Demagnetisation, allowing for smooth control with virtually all powertrain combinations with peak power outputs of up to 9 kW.

NDAA/DFARS-compliant options are available upon request.

New Feature Set (V2)

• Configuration of drive parameters, signal types and fault handling

• Bi-Directional DShot for RPM Filtering support

• On board bootloader

• Passthrough firmware updating and configuration

• Additional Telemetry types: PWM Telemetry and RPM Output

• High-speed telemetry rates when operating DShot and ProShot

• Reversible operation support (full forwards to full reverse)

• Dynamic signal quality checks across supported input protocols

• Hardware protection for UART programming pins Existing Feature Set

Existing Feature:

• Designed and manufactured in Australia using only the highest quality components, ensuring no sacrifice in reliability

• Proprietary firmware designed in Australia

• Plug and play firmware

• Up to 12S (50.4 V) capable

• Up to 120 A continuous* output current

• 200 A Burst current

• True 10-bit resolution

• Virtually no setup time, with a simple motor reverse solder tab

• Auto-detect ProShot or DShot

• ProShot1000 capable (1Mbs/s)

• DShot150 to DShot600 capable (0.15-0.6Mbs/s)

• Up to 750,000 eRPM (protocol dependant)

• Motor agnostic

• Auto PWM output frequency

• Auto timing advance

• Telemetry output

• Automatic current limiting and over-temperature protection

• LED indication

• Digital commands over ProShot (including anti-turtle mode)

• Digital commands over DShot

• Bare-PCB design to allow maximum integration within the end setup

• 8-Layer PCB to ensure minimal track resistance

* Continuous current ratings are at a 100% throttle duty cycle. Continuous rating is defined as max sustained current at 100% throttle for 60 seconds with 33 m/s of airflow.

Documentation and Datasheets can be found at: docs.powerdrives.net

Additional Information

Weight: 0.02kg

Dimensions: 70x30x20mm

Documentation: docs.powerdrives.net

CAD Model: 120F3 CAD Model

The improved F_Series 80F3[X] ESCs. Building upon our trusted ARM 32-bit architecture, the V2 release features introduce a number of highly requested features into the product range, including configuration options, Bi-Directional DShot, and UART overvoltage protection. The 80F3[X]v2 ESCs are drop-in replaceable to 80F3[X] units. As before, existing features include PWM-frequency dithering and Active Phase-Current Demagnetisation, allowing for smooth control with virtually all powertrain combinations with peak power outputs of up to 4.7 kW.

NDAA/DFARS-compliant options available upon request.

New Feature Set (V2)

• Configuration of drive parameters, signal types and fault handling

• Bi-Directional DShot for RPM Filtering support

• On board bootloader

• Passthrough firmware updating and configuration

• Additional Telemetry types: PWM Telemetry and RPM Output

• High-speed telemetry rates when operating DShot and ProShot

• Reversible operation support (full forwards to full reverse)

• Dynamic signal quality checks across supported input protocols

• Hardware protection for UART programming pins

Feature Set

• Designed and manufactured in Australia using only the highest quality components, ensuring no sacrifice in reliability

• Proprietary firmware designed in Australia

• Plug and play firmware

• Up to 8S (34 V) capable

• Up to 80 A continuous* output current

• 140 A Burst current

• True 10-bit resolution

• Virtually no setup time, with simple motor reverse solder tab

• Auto-detect ProShot or DShot

• ProShot1000 capable (1Mbs/s)

• DShot150 to DShot600 capable (0.15-0.6Mbs/s)

• Up to 750,000 eRPM (protocol dependant)

• Motor agnostic

• Auto PWM output frequency

• Auto timing advance

• Telemetry output

• Automatic current limiting and over-temperature protection

• LED indication

• Digital commands over ProShot (including anti-turtle mode)

• Digital commands over DShot

• Bare-PCB design to allow maximum integration within the end setup

• 8-Layer PCB to ensure minimal track resistance

* Continuous current ratings are at a 100% throttle duty cycle. Continuous rating is defined as max sustained current at 100% throttle for 60 seconds with 33 m/s of airflow.

Documentation and Datasheets can be found at: docs.powerdrives.net

Additional Information

Weight: 0.02kg

Dimensions: 44x22x12mm

Documentation: docs.powerdrives.net

CAD Model: 80F3 CAD Model

The F_Series ESCs are built from the ground up upon trusted 32-bit ARM architecture to ensure performance is maximised for a wide range of operating environments. Features including PWM-frequency dithering and Active Phase-Current Demagnetisation allow for smooth control with virtually all powertrain combinations with peak power outputs of up to 2.5 kW.

NDAA/DFARS-compliant options available upon request.

Feature Set:

• Designed and manufactured in Australia using only the highest quality components, ensuring no sacrifice in reliability

• Proprietary firmware designed in Australia

• Plug and play firmware

• Up to 6S (25.5 V) capable

• Up to 40 A continuous* output current

• 100 A Burst current

• True 10-bit resolution

• Virtually no setup time, with simple motor reverse solder tab

• Auto-detect ProShot or DShot

• ProShot1000 capable (1Mbs/s)

• DShot300 to DShot1200 capable (0.3-1.2Mbs/s)

• Up to 750,000 eRPM

• Motor agnostic

• Auto PWM output frequency

• Auto timing advance

• Telemetry output

• Automatic current limiting and over-temperature protection

• LED indication

• Digital commands over ProShot (including anti-turtle mode)

• Digital commands over DShot

• Bare-PCB design to allow maximum integration within the end setup

• 8-Layer PCB to ensure minimal track resistance

* Continuous current ratings are at a 100% throttle duty cycle. Continuous rating is defined as max sustained current at 100% throttle for 60 seconds with 33 m/s of airflow.

Documentation and Datasheets can be found at: docs.powerdrives.net

Additional Information

Weight: 0.003kg

Dimensions: 16x30x5mm

Documentation: docs.powerdrives.net

CAD Model: 40F3